Knowledge

What Is a Lift Type Check Valve? Working Principle and Specifications

May 30, 2025 Leave a message

Definition and Function

A lift type check valve is a valve that opens and closes automatically according to the direction of flow, blocking reverse movement of the medium and so protecting the pipeline system. It belongs to the family of automatic valves, and in Chinese practice it is also called a non return valve, a one way valve or a back pressure valve.

Its core function is to prevent the medium from running back, which in turn prevents pumps and motors from reversing, protects equipment from a pressure surge arriving from downstream, and isolates auxiliary systems that may be at a higher pressure than the main line.

Structural Features

Disc movement. The disc slides up and down along the vertical centreline of the body, and the movement trajectory is parallel to the seat axis. A guide rod on the disc runs inside a guide sleeve in the bonnet, and that guide is what gives the design its characteristic stability and its tight reseating.

Key components. The sealing surfaces are hardfaced or coated with tungsten carbide or a cobalt based hard alloy to resist high temperature and erosion from particle containing media. Some models integrate a spring behind the disc, which assists closing and reduces the risk of leakage in low pressure or low flow conditions. Body patterns include flanged, wafer and threaded designs, following the usual Chinese model coding of H41H for the flanged lift check, H71H for the wafer pattern and H11H for the threaded pattern, covering nominal diameters from DN15 to about DN800.

Materials. Carbon steel WCB for general duty, stainless steel CF8 and CF8M for corrosive service, chrome molybdenum steel such as WC6 and WC9 for high temperature steam, and low temperature grades for refrigeration.

Working Principle

When flow moves in the normal direction, the fluid pressure lifts the disc clear of the seat, the passage opens fully, and the disc is held in the open position by the flow itself. When the flow stops or reverses, the disc falls back onto the sealing surface under its own weight together with the reverse pressure acting on it, and the spring, where fitted, accelerates that return so that the valve shuts before a significant reverse velocity can develop.

The design consequence is a trade off that matters in selection. Because the flow has to lift the disc out of the passage and turn through the body, a lift check valve has a higher flow resistance coefficient than a swing check valve of the same bore, and the pressure loss can be several times larger. In return, the guided disc seats accurately and gives tighter shutoff, which is why the type is preferred for small bore, high pressure duty where sealing quality matters more than pressure loss.

Performance, Ratings and Comparison

Parameter Lift type check valve
Disc motion Slides along the seat axis, guided by rod and sleeve
Pressure class Class 150 to Class 2500, with ratings read from ASME B16.34
Temperature range About -29 degC to 425 degC for carbon steel bodies, extended to around 550 degC with alloy steel bodies and hardfaced trim
Leakage test Shell and seat tightness to API 598
Flow resistance Higher than a swing check valve because of the change of flow direction
Installation Traditionally horizontal; spring assisted and double guided designs can be used in vertical pipe

Compared with a dual plate check valve, the lift type is simpler in construction but longer in face to face dimension and higher in pressure loss. Compared with a swing check valve, it seals better but resists flow more. The choice therefore follows the duty: tight closure and stable behaviour at low flow favour the lift type, while large bore and low pressure loss favour the swing type.

Applications and Installation

Petrochemical. High temperature oil and process lines in refineries and chemical plants, with stainless steel or alloy steel trim for corrosion and temperature resistance.

Power generation. Boiler feedwater and heater drain lines, where forged or cast steel bodies rated for high pressure are used and tight shutoff protects the pump.

Water and wastewater. Anti-backflow protection at the discharge of sewage and process pumps, including wafer patterns with spring assisted closing.

Installation follows three rules. The arrow on the body must be aligned with the normal direction of flow, because a lift check valve fitted backwards will not open at all. The valve should be mounted in the orientation permitted by its design: a vertical line needs a spring assisted or double guided model rather than a plain horizontal pattern. And because the disc depends on free movement in the guide, the upstream pipe should be cleaned of weld slag and debris before commissioning, so that the disc cannot be held off its seat by foreign material.

For maintenance, the guide sleeve and guide rod should be inspected periodically for wear, and the guide clearance should be restored to the manufacturer's limit when it becomes excessive. On particle containing service the seat sealing surface should be cleaned at each planned shutdown, since deposits on the seat are the most common cause of a check valve that weeps.

FAQ

Q: What is the main difference between a lift check valve and a swing check valve?
The disc movement. A lift check valve disc slides along the seat axis and reseats accurately, giving better tightness but higher pressure loss. A swing check valve disc rotates about a hinge pin and offers lower pressure loss but less precise seating.

Q: Does the flow resistance of a lift check valve matter in selection?
Yes. Because the flow must lift the disc and change direction, the resistance is higher than a swing check valve of the same bore. The lift type is therefore chosen where sealing quality matters more than pressure loss.

Q: Can a lift check valve be installed in a vertical pipe?
Only with a design that suits it, such as a spring assisted or double guided model. A plain pattern intended for horizontal installation may not close reliably in a vertical line.

Q: What pressure and temperature range does the design cover?
Class 150 to Class 2500 according to ASME B16.34. Carbon steel bodies cover roughly -29 degC to 425 degC, and alloy steel bodies with hardfaced trim extend service to about 550 degC.

Q: Why is a spring fitted in some lift check valves?
The spring closes the disc faster and keeps it loaded against the seat at low flow, which reduces leakage risk and limits reverse flow before it develops in pump discharge duty.

Q: How is the valve tested before delivery?
A shell pressure test and a seat tightness test are performed to API 598 at the specified pressures, and the results are recorded together with the body and trim material certificates.

Send Inquiry