Knowledge

Check Valve Function: How It Works, Types & Applications

Apr 16, 2025 Leave a message

1. What Is a Check Valve and What Does It Do?

A check valve (also called a non-return valve) is an automatic, self-actuated valve that allows fluid to flow in one direction only. Its disc, flap or ball opens when the upstream pressure exceeds the downstream pressure plus the cracking force, and closes automatically as soon as the flow tries to reverse. Because the valve is driven entirely by the medium, it needs no operator, actuator or external power. The single most important function of a check valve is backflow prevention: in a pump discharge line, it stops pressurized fluid from flowing back through the pump when the pump stops, protecting the impeller from reverse rotation and the motor and transmission from reverse torque. In pipeline systems it prevents sudden pressure surges from propagating backwards, avoids draining of filled columns, and keeps separate circuits from cross-contaminating each other.

2. Working Principle and Main Types

All check valves work on the same principle - differential pressure across the disc - but the disc motion differs by type, which changes flow resistance, sealing behaviour and acceptable installation orientation:

Type Disc motion Flow resistance Typical applications Orientation
Swing check valve Disc rotates on a hinge pin Low Municipal water mains, large pipelines, pump discharge with moderate velocity Horizontal (or vertical with upward flow)
Lift check valve Disc lifts vertically in a guide Higher High-pressure, small-diameter lines (chemical pump outlets) Horizontal (vertical versions available)
Dual plate (wafer) check valve Two spring-loaded half-discs Very low, short stroke Space-constrained plants, ship systems, HVAC, API 594 short face-to-face Any (spring-assisted closure)
Tilting disc / non-slam check valve Disc tilts around an eccentric pivot, counterweight or dashpot Low Large pumps and compressors where water hammer must be minimized Horizontal

For the great majority of industrial duties, the swing type is chosen where pressure drop matters most, the lift type where tight sealing and high pressure are required, and the dual-plate type where installation length and weight are constrained.

3. Materials and Performance

Check valve bodies and trims follow the same material logic as other pipeline valves: cast carbon steel (WCB per ASTM A216) for general service, cast stainless steel (CF8/CF8M per ASTM A351) for corrosive media, and 304/316 wrought stainless for wafer or fabricated designs. Duplex and super-duplex grades (e.g., 2205) are specified for seawater, chloride-laden brines and sour gas service, where their higher strength and pitting resistance justify the premium. Seats and discs are commonly hard-faced with a cobalt- or nickel-based alloy to resist erosion in high-velocity or particulate media. Design and testing follow API 594 (face-to-face dimensions and dual-plate check valve requirements), API 598 (shell and seat test acceptance) and ASME B16.34 (pressure-temperature ratings); for pipeline duty, API 6D applies. Selecting a valve with a documented test certificate to one of these standards is the fastest way to de-risk a purchase.

4. Installation and Selection Key Points

Flow direction: the arrow on the body is not optional. A reverse-installed check valve locks the line closed (or fails open, depending on type), so verify orientation before bolting up.

Orientation limits: lift check valves generally require horizontal mounting with the disc vertical; swing check valves are normally horizontal but may be installed vertically with upward flow; dual-plate and spring-loaded types tolerate any orientation.

Water hammer (slam): in long discharge lines with rapid pump shutdown, a fast-closing conventional swing check can slam, generating pressure spikes several times the working pressure. Use a non-slam (tilting disc or spring-assisted) design, or slow the closure, where surge analysis shows high velocities.

Minimum flow: every check valve needs a minimum differential pressure to hold the disc fully open. Continuous operation below this threshold causes disc flutter and rapid seat wear.

Location: install downstream of the pump discharge (typically after the isolation valve, or between pump and isolation valve per project convention) and upstream of any equipment that must not see reverse flow.

5. Common Misconceptions

Three mistakes recur in the field. First, "a check valve provides backflow protection by itself" - it protects against flow reversal, but if backflow of contaminated water into a potable supply is a concern, a dedicated backflow preventer (not a plain check valve) is required by most water codes. Second, "harder seating material means a better valve" - metal-to-metal seats offer durability but limited shutoff tightness; for bubble-tight closure at low pressure, resilient or soft seats are superior, and the two are not interchangeable without a sealing-class check. Third, "any check valve can be buried or installed vertically" - orientation and accessibility rules vary by type, and buried service demands a design validated for that duty (e.g., ductile iron swing check with protective coating).

6. FAQ

What happens if a system has no check valve? When the pump stops or the downstream pressure rises, fluid flows back, spinning the pump impeller in reverse and subjecting the motor to reverse torque. Return flow also drains the discharge column, so the next start-up runs against an empty line, risking water hammer and impeller damage.

What is the difference between a swing check valve and a lift check valve? swing check uses a hinged disc that rotates fully out of the flow path, giving low pressure drop; a lift check raises its disc vertically, giving tighter sealing but higher flow resistance. Swing types suit large, low-velocity lines; lift types suit smaller, higher-pressure duties.

Can a check valve be installed vertically? Spring-loaded types (dual plate, spring-assisted swing/lift) can. A plain lift check valve must normally be horizontal; a conventional swing check may be mounted vertically only with upward flow so the disc falls closed by gravity.

How do I stop water hammer caused by a check valve? Choose a non-slam design (tilting disc, spring-assisted dual plate) or fit a dashpot/retarder on the lever of a large swing check. Surge analysis of the line velocity and pump stop time should drive the decision.

Which standards apply to industrial check valves? API 594 covers check valve face-to-face dimensions and dual-plate valves; API 598 defines shell and seat test acceptance; ASME B16.34 governs pressure-temperature ratings; API 6D applies to pipeline check valves. Ask the supplier for certificates to these standards.

Why does my check valve rattle or vibrate at low flow? The disc is fluttering because the differential pressure is below the valve's minimum opening requirement. Operate above the minimum continuous flow, or select a lighter-disc / spring-assisted type with a lower cracking pressure.

Swing, lift or dual-plate - tell us your media, pressure and size, and we will recommend the right check valve.

Frequently Asked Questions

Why does a check valve operate without an operator, actuator or external power? check valve is an automatic, self-actuated valve driven entirely by the medium. Its disc, flap or ball opens when the upstream pressure exceeds the downstream pressure plus the cracking force, and closes automatically as soon as the flow tries to reverse, which makes it reliable in unattended and remote installations.

Which materials are specified for check valves in seawater and sour gas service? Duplex and super-duplex grades such as 2205 are specified for seawater, chloride-laden brines and sour gas, where their higher strength and pitting resistance justify the premium. WCB carbon steel (ASTM A216) covers general service, CF8/CF8M stainless (ASTM A351) suits corrosive media, and 304/316 wrought stainless is used for wafer or fabricated designs, with cobalt- or nickel-based hard facing on seats and discs for erosive duty.

Where should a check valve be installed in a pump discharge line? Install it downstream of the pump discharge, typically after the isolation valve or between the pump and the isolation valve per project convention, and upstream of any equipment that must not see reverse flow. The flow arrow on the body is not optional - a reverse-installed check valve locks the line closed or fails open, so verify orientation before bolting up.

When is a plain check valve not sufficient for backflow protection? check valve protects against flow reversal, but if backflow of contaminated water into a potable supply is a concern, most water codes require a dedicated backflow preventer rather than a plain check valve. Confirm the code requirement for the specific hazard before relying on a check valve alone.

Why is a metal-to-metal seat not automatically better than a resilient seat on a check valve? Metal-to-metal seating offers durability in erosive or high-temperature service but gives limited shutoff tightness. For bubble-tight closure at low pressure, resilient or soft seats are superior, and the two constructions are not interchangeable without re-checking the sealing class required by the duty.

Which check valve type suits space-constrained plants and ship systems? Dual-plate (wafer) check valves suit these duties: two spring-loaded half-discs give very low flow resistance with a short stroke, tolerate any installation orientation thanks to spring-assisted closure, and comply with the API 594 short face-to-face pattern that keeps the package compact.

Send Inquiry