Products
Flanged Ball Valves
video
Flanged Ball Valves

Flanged Ball Valves

The flange ball valve only needs to be rotated 90 degrees and a small rotational torque to close tightly. The completely equal valve body cavity provides a straight flow path with little resistance for the medium.

A flanged ball valve is a quarter-turn valve that bolts directly between two pipe flanges. A quarter turn of the lever rotates a bored ball inside the body so the flow either passes straight through or stops completely. When the ball bore lines up with the pipe, the valve is open; turned 90 degrees across the flow, it seals shut.

Because the body cavity is sized to match the pipe bore, media moves through a straight, unobstructed path with very little pressure loss. That straight-through design, combined with a simple lever and a compact body, is why flanged ball valves are common wherever a line needs reliable, fast shut-off that can be serviced without cutting the pipe.

 

How a Flanged Ball Valve Works

The ball sits between two seats, one on each side. In the open position, fluid passes through the bore in the ball. Turning the handle rotates the ball through 90 degrees and presses its solid face against the downstream seat, cutting off the flow. Sealing comes from the two soft seats (normally PTFE) held against the ball, not from tightening the handle.

Two design details matter here. A floating ball valve lets the ball move slightly downstream under pressure so it pushes harder against the downstream seat - the higher the pressure, the tighter the seal. A trunnion-mounted ball is held by bearings top and bottom, which keeps operating torque low on larger sizes and higher pressures.

 

Specification

Parameter

Specification

Design standard

EN 1983 (formerly DIN 3357), API 608

Face-to-face

EN 558-1, DIN 3202, ASME B16.10

Flange drilling

EN 1092-2, ASME B16.5, JIS B2220

Pressure rating

PN10, PN16, PN25, PN40; Class 150 / Class 300

Size range

DN15 – DN300 (1/2" – 12")

Body material

Cast iron, ductile iron, WCB, CF8 (SS304), CF8M (SS316)

Ball & stem

SS304, SS316, ASTM A351 CF8 / CF8M

Seat material

PTFE; RPTFE or PEEK for higher temperature

Bolting

SS304

Temperature

-25°C to +150°C (PTFE seat)

Operation

Lever handle; gear or actuator available on request

End connection

Flanged, raised face (FF / RF)

 

Body Configurations

Flanged ball valves come in one-piece, two-piece, and three-piece bodies, and the choice changes how the valve is maintained.

One-piece - the body is cast or forged in a single piece, so the ball and seats are installed through the end. It is the least expensive and has no bolted joints to leak, but it cannot be repaired in line; the whole valve comes out if a seat wears.

Two-piece - the body splits into two halves bolted together. The valve can be opened for seat and ball replacement, though it normally still has to be removed from the line.

Three-piece - two end caps bolt to a central body. The middle section swings out without disturbing the pipe connections, which makes seat replacement fast and cheap.

 

Material Selection

The body material is chosen to match the line media, pressure, and temperature:

Cast iron and ductile iron cover general water, air, and non-corrosive service at moderate pressure.

WCB (carbon steel) suits higher pressure and temperature in process lines.

CF8 (SS304) and CF8M (SS316) handle corrosive media; the molybdenum in CF8M improves pitting resistance in chloride and mild acid service.

In all of these valves the ball and stem are normally stainless steel so the wetted metal parts stay clean, while the soft PTFE seats do the actual sealing.

 

Sealing and Temperature Limits

PTFE seats hold a wide range of media but are limited to roughly -25°C to +150°C. Above that the material softens and the seal fails early - the most common reason a flanged ball valve leaks after being put on hot service. For steam, hot oil, or other media above 150°C, specify RPTFE (reinforced) or PEEK seats, and confirm the temperature-pressure rating with the manufacturer before ordering.

 

Typical Applications

Flanged ball valves turn up wherever a line needs positive shut-off and occasional isolation:

Water treatment and municipal supply lines

HVAC chilled and hot water circuits

Chemical transfer, including acids, solvents, and oxygen service

Natural gas and compressed air distribution

Oil and petrochemical process lines

Fire protection systems

Flanged ends make them the natural choice on larger lines (roughly DN50 and up) and on services that must be taken apart for cleaning or inspection.

 

How to Select a Flanged Ball Valve

A spec that looks complete on paper often misses one detail that decides how long the valve lasts. Check these before ordering:

Media and temperature - this sets the seat material more than the body material.

Pressure class - match the valve's PN or Class rating to the line flange rating; do not mix PN and Class flanges on the same joint.

Body material - pick for corrosion resistance and pressure, not just cost.

Size and bore - confirm whether you need full bore (no flow restriction, required for pigging or slurries) or reduced bore (lighter and cheaper).

Flange standard - EN 1092, ASME B16.5, or JIS; the bolt pattern must match the existing pipe flange.

Operation - a lever is fine up to about DN150; above that, gear operators or actuators keep torque manageable.

 

Testing and Inspection

Every valve is pressure tested before it leaves the factory. A shell test pressurizes the body to confirm no leakage through the casting, and a seat test confirms the ball seals tight at the rated pressure. Standard test procedures follow API 598 or EN 12266-1. For oxygen or other critical service, valves are also degreased and cleaned before packing.

 

flanged ball valves ready for shipment

stainless steel flanged ball valves ready for shipment
stainless steel flanged ball valves
flanged ball valves
 
 
 

Contact now for Flanged Ball Valves

 

FAQ

Q: Do you have a minimum order quantity?

A: No. We accept sample orders so you can test quality first. Unit price drops as quantity increases.

 

Q: Do you test every valve before delivery?

A: Yes, each valve is 100% tested - shell and seat pressure tests, plus additional checks such as spark or hydro test where the service calls for it.

 

Q: What is the difference between full bore and reduced bore?

A: A full-bore valve has a ball opening the same size as the pipe, so there is no flow restriction. A reduced-bore valve has a smaller ball opening; it costs and weighs less, but it adds a small pressure drop and cannot be used for pigging.

 

Q: Can a flanged ball valve handle steam?

A: Only if it is specified for it. A standard PTFE-seated valve is limited to about 150°C. Steam service needs RPTFE or PEEK seats and a derated pressure rating - confirm both with the supplier.

 

Q: What flange standards do you match?

A: We machine flanges to EN 1092-2, ASME B16.5, and JIS B2220, so the bolt pattern matches your existing piping. Let us know the standard and rating when you enquire.

 

Hot Tags: flanged ball valves, China flanged ball valves manufacturers, suppliers, factory, ball valve acoustic couplings, ball valve clutch actuators, ball valve protection, ball valve purchase, Double Block and Bleed Valves, ball valve balls

Send Inquiry